Quadro Quadro2x2 Guia de Instalação descarregar pdf (Página 23)

QuadroM 32x/8L/26x/12Li/26xi Manual I: Installation Guide Step 1: Installing the Quadro

Wires are presented in the table below:

Color Pin (Tip) Pin (Ring) Color FXS Port

White/Blue 26 1 Blue/White 3

White/Orange 27 2 Orange/White 4

White/Green 28 3 Green/White 5

White/Brown 29 4 Brown/White 6

White/Slate 30 5 Slate/White 7

Red/Blue 31 6 Blue/Red 8

Red/Orange 32 7 Orange/Red 9

Red/Green 33 8 Green/Red 10

Red/Brown 34 9 Brown/Red 11

Red/Slate 35 10 Slate/Red 12

Black/Blue 36 11 Blue/Black 13

Black/Orange 37 12 Orange/Black 14

Black/Green 38 13 Green/Black 15

Black/Brown 39 14 Brown/Black 16

Black/Slate 40 15 Slate/Black 17

Yellow/Blue 41 16 Blue/Yellow 18

Yellow/Orange 42 17 Orange/Yellow 19

Yellow/Green 43 18 Green/Yellow 20

Yellow/Brown 44 19 Brown/Yellow 21

Yellow/Slate 45 20 Slate/Yellow 22

Violet/Blue 46 21 Blue/Violet 23

Violet/Orange 47 22 Orange/Violet 24

Violet/Green 48 23 Green/Violet 25

Violet/Brown 49 24 Brown/Violet 26

Violet/Slate 50 25 Slate/Violet Not Used

• Verify the product package contents are complete. Refer to the contents sheet included

in the packaging to determine if all the items were shipped in the box.

• Before you connect the hardware, make sure that all devices are powered off.

• Connect analog phones to the PHONE ports on the Quadro’s rear panel. You may

connect up to two analog phones.

• Connect the E1/T1 port to your PBX or the trunk from the PSTN Central Office Only

after configuring the E1/T1 settings according to the specifications of your PSTN provider

(see Appendix: Pin Assignment of E1/T1

• Connect the Ethernet port on your PC via a straight CAT 5 cable with an RJ45 connec-

tor to the LAN socket of the Quadro.

• Connect the IP phones to the switch and attach it to the LAN socket of the Quadro via a

straight CAT 5 cable with an RJ45 connector.

• Connect the WAN port of the Quadro to the Internet service via a cable or DSL modem.

• Power up the DSL or Cable modem first.

• Connect the power cable to the POWER port on the back side of your QuadroM and

plug the power plug into the power outlet.

The red LED (Fault) will glow for several seconds followed by the yellow LED (Info),

which will glow for several minutes. When Info LED is off, the Quadro is operational.

• Power up any hub or switch followed by any PC and other devices on the LAN side.

• Check the LEDs: The green Busy LED must glow continuously. The green ETH, LAN

and WAN LEDs will blink when cables are connected to these ports and all devices are

powered up. If the green LAN and WAN LEDs do not blink, verify cabling and ensure

that all devices are powered up.

QuadroM 32x/8L/26x/12Li/26xi; (SW Version 5.2.x) 23

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 75 76

Comentários a estes Manuais

Sem comentários

Quadro Quadro2x2 Guia de Instalação Página 23

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de troca automática de ramais privados (PBX) Quadro Quadro2x2